FreeBSD manual
download PDF document: fifolog_create.1.pdf
FIFOLOG(1) FreeBSD General Commands Manual FIFOLOG(1)
NAME
fifolog_create, fifolog_writer, fifolog_reader - initialize, write, seek
and extract data from a fifolog
SYNOPSIS
fifolog_create [-l record-size] [-r record-count] [-s size] file
fifolog_reader [-t] [-b tstart] [-B Tstart] [-e tend] [-E Tend]
[-o ofile] [-R regexp] [-T timefmt] file
fifolog_writer [-w write-rate] [-s sync-rate] [-z compression] file
DESCRIPTION
Fifologs provide a compact round-robin circular storage for recording
text and binary information to permanent storage in a bounded and
predictable fashion, time and space wise.
A fifolog can be stored either directly on a disk partition or in a
regular file.
The input data stream is encoded, compressed and marked up with
timestamps before it is written to storage, such that it is possible to
seek out a particular time interval in the stored data, without having to
decompress the entire logfile.
The fifolog_create utility is used to initialize the first sector of a
disk device or file system file to make it a fifolog and should be called
only once.
Running fifolog_create on an existing fifolog will reset it so that
fifolog_reader and fifolog_writer will not see the previous contents.
(The previous contents are not physically erased, and with a bit of hand-
work all but the first record can be easily recovered.)
If the file does not already exist, fifolog_create will attempt to create
and ftruncate(2) it to the specified size, defaulting to 86400 records of
512 bytes if the -r, -l or -s options do not specify otherwise.
The fifolog_writer utility will read standard input and write it to the
end of the fifolog according to the parameters given.
Writes happen whenever the output buffer is filled with compressed data
or when either of two timers expire, forcing a partially filled buffer to
be written.
The first and faster timer, -w write-rate, forces available data to be
written but does not flush and reset the compression dictionary. This
timer is intended to minimize the amount of logdata lost in RAM in case
of a crash and by default it fires 10 seconds after the previous write.
The second and slower timer, -s sync-rate, forces a full flush and reset
of the compression engine and causes the next record written to be a
synchronization point with an uncompressed timestamp, making it possible
to start reading the logfile from that record. By default this timer
fires a minute after the previous sync.
The -z compression option controls the zlib(3) compression level; legal
values are zero to nine which is the default.
readable specifications such as "1 hour ago".
The -t option forces timestamps to be formatted as "YYYYMMDDhhmmss"
instead of as time_t, and -T allows the specification of an strftime(3)
formatting string.
Finally, records can be filtered such that only records matching the
(REG_BASIC) regular expression specified with -R are output.
IMPLEMENTATION NOTES
The data stored in the fifolog consists of three layers, an outer layer
that allows searches to synchronization points based on timestamps
without having to decompress and decode the actual contents, a
compression layer implemented with zlib(3), and an inner serialization
and timestamping layer.
The exact encoding is described in the fifolog.h file.
Fifolog is particularly well suited for use on Flash based media, where
it results in much lower write-wear, than a file system with regular log
files rotated with newsyslog(8) etc.
EXAMPLES
Create a fifolog with 1024*1024 records of 512 bytes:
fifolog_create -r 10m /tmp/fifolog
Write a single record to this file:
date | fifolog_writer /tmp/fifolog
Read it back with human readable timestamps:
fifolog_reader -t /tmp/fifolog
One particular useful use of fifolog_writer is with syslogd(8) using a
line such as this in syslog.conf(5):
*.* |fifolog_writer /var/log/syslog_fifolog
HISTORY
The fifolog tools have been liberated from an open source SCADA
applications called "measured", which monitors and controls remote radio
navigation transmitters for the Danish Air Traffic Control system.
AUTHORS
The fifolog tools were written by Poul-Henning Kamp.
FreeBSD 14.0-RELEASE-p11 February 9, 2008 FreeBSD 14.0-RELEASE-p11