• Start
• Documentation
  • PostgreSQL
  • mnoGoSearch
  • Apache 2.4
  • FreeBSD handbook
  • FreeBSD Manual
  • FreeBSD Source
• Tools
• Search
• Protected Area

plain

FreeBSD manual

keyword 1 2 3 4 5 6 7 8 9 n l

download PDF document: gpio.4.pdf

GPIO(4) FreeBSD Kernel Interfaces Manual GPIO(4)
NAME gpiobus - GPIO bus system
SYNOPSIS To compile these devices into your kernel and use the device hints, place the following lines in your kernel configuration file:
device gpio device gpioc device gpioiic device gpioled
Additional device entries for the ARM architecture include:
device a10_gpio device bcm_gpio device imx51_gpio device lpcgpio device mv_gpio device ti_gpio device gpio_avila device gpio_cambria device zy7_gpio device pxagpio
Additional device entries for the MIPS architecture include:
device ar71xxx_gpio device octeon_gpio device rt305_gpio
Additional device entries for the POWERPC architecture include:
device wiigpio device macgpio
Additional device entries for the RISC-V architecture include:
device sifive_gpio
DESCRIPTION The gpiobus system provides a simple interface to the GPIO pins that are usually available on embedded architectures and can provide bit banging style devices to the system.
The acronym GPIO means "General-Purpose Input/Output."
The BUS physically consists of multiple pins that can be configured for input/output, IRQ delivery, SDA/SCL iicbus use, etc.
On some embedded architectures (like MIPS), discovery of the bus and configuration of the pins is done via device.hints(5) in the platform's kernel config(5) file.
On some others (like ARM), where FDT(4) is used to describe the device tree, the bus discovery is done via the DTS passed to the kernel, being either statically compiled in, or by a variety of ways where the boot example, "gpiobus0". driver and unit are the driver name and the unit number for the device driver.
hint.driver.unit.pins This is a bitmask of the pins on the gpiobus that are connected to the device. The pins will be allocated to the specified driver instance. Only pins with numbers from 0 to 31 can be specified using this hint.
hint.driver.unit.pin_list This is a list of pin numbers of pins on the gpiobus that are connected to the device. The pins will be allocated to the specified driver instance. This is a more user friendly alternative to the pins hint. Additionally, this hint allows specifying pin numbers greater than 31. The numbers can be decimal or hexadecimal with 0x prefix. Any non-digit character can be used as a separator. For example, it can be a comma, a slash or a space. The separator can be followed by any number of space characters.
The following device.hints(5) are only provided by the ar71xx_gpio driver:
hint.gpio.%d.pinmask This is a bitmask of pins on the GPIO board that we would like to expose for use to the host operating system. To expose pin 0, 4 and 7, use the bitmask of 10010001 converted to the hexadecimal value 0x0091.
hint.gpio.%d.pinon This is a bitmask of pins on the GPIO board that will be set to ON at host start. To set pin 2, 5 and 13 to be set ON at boot, use the bitmask of 10000000010010 converted to the hexadecimal value 0x2012.
hint.gpio.function_set
hint.gpio.function_clear These are bitmasks of pins that will remap a pin to handle a specific function (USB, UART TX/RX, etc) in the Atheros function registers. This is mainly used to set/clear functions that we need when they are set up or not set up by uBoot.
Simply put, each pin of the GPIO interface is connected to an input/output of some device in a system.
SEE ALSO gpioiic(4), gpioled(4), iicbus(4), device.hints(5), gpioctl(8)
HISTORY The gpiobus manual page first appeared in FreeBSD 10.0.
AUTHORS This manual page was written by Sean Bruno <sbruno@FreeBSD.org>.