FreeBSD manual
download PDF document: if_gif.4.pdf
GIF(4) FreeBSD Kernel Interfaces Manual GIF(4)
NAME
gif - generic tunnel interface
SYNOPSIS
device gif
DESCRIPTION
The gif interface is a generic tunnelling device for IPv4 and IPv6. It
can tunnel IPv[46] traffic over IPv[46]. Therefore, there can be four
possible configurations. The behavior of gif is mainly based on RFC2893
IPv6-over-IPv4 configured tunnel. On NetBSD, gif can also tunnel ISO
traffic over IPv[46] using EON encapsulation. Note that gif does not
perform GRE encapsulation; use gre(4) for GRE encapsulation.
Each gif interface is created at runtime using interface cloning. This
is most easily done with the "ifconfig create" command or using the
ifconfig_<interface> variable in rc.conf(5).
To use gif, the administrator needs to configure the protocol and
addresses used for the outer header. This can be done by using
ifconfig(8) tunnel, or SIOCSIFPHYADDR ioctl. The administrator also
needs to configure the protocol and addresses for the inner header, with
ifconfig(8). Note that IPv6 link-local addresses (those that start with
fe80::) will be automatically configured whenever possible. You may need
to remove IPv6 link-local addresses manually using ifconfig(8), if you
want to disable the use of IPv6 as the inner header (for example, if you
need a pure IPv4-over-IPv6 tunnel). Finally, you must modify the routing
table to route the packets through the gif interface.
The gif device can be configured to be ECN friendly. This can be
configured by IFF_LINK1.
ECN friendly behavior
The gif device can be configured to be ECN friendly, as described in
draft-ietf-ipsec-ecn-02.txt. This is turned off by default, and can be
turned on by the IFF_LINK1 interface flag.
Without IFF_LINK1, gif will show normal behavior, as described in
RFC2893. This can be summarized as follows:
Ingress Set outer TOS bit to 0.
Egress Drop outer TOS bit.
With IFF_LINK1, gif will copy ECN bits (0x02 and 0x01 on IPv4 TOS byte or
IPv6 traffic class byte) on egress and ingress, as follows:
Ingress Copy TOS bits except for ECN CE (masked with 0xfe) from
inner to outer. Set ECN CE bit to 0.
Egress Use inner TOS bits with some change. If outer ECN CE bit
is 1, enable ECN CE bit on the inner.
Note that the ECN friendly behavior violates RFC2893. This should be
used in mutual agreement with the peer.
Security
Miscellaneous
By default, gif tunnels may not be nested. This behavior may be modified
at runtime by setting the sysctl(8) variable net.link.gif.max_nesting to
the desired level of nesting.
SEE ALSO
gre(4), inet(4), inet6(4), ifconfig(8)
R. Gilligan and E. Nordmark, "Transition Mechanisms for IPv6 Hosts and
Routers", RFC2893, http://tools.ietf.org/html/rfc2893, August 2000.
Sally Floyd, David L. Black, and K. K. Ramakrishnan, IPsec Interactions
with ECN, December 1999, draft-ietf-ipsec-ecn-02.txt.
HISTORY
The gif device first appeared in the WIDE hydrangea IPv6 kit.
BUGS
There are many tunnelling protocol specifications, all defined
differently from each other. The gif device may not interoperate with
peers which are based on different specifications, and are picky about
outer header fields. For example, you cannot usually use gif to talk
with IPsec devices that use IPsec tunnel mode.
If the outer protocol is IPv4, gif does not try to perform path MTU
discovery for the encapsulated packet (DF bit is set to 0).
If the outer protocol is IPv6, path MTU discovery for encapsulated
packets may affect communication over the interface. The first bigger-
than-pmtu packet may be lost. To avoid the problem, you may want to set
the interface MTU for gif to 1240 or smaller, when the outer header is
IPv6 and the inner header is IPv4.
The gif device does not translate ICMP messages for the outer header into
the inner header.
In the past, gif had a multi-destination behavior, configurable via
IFF_LINK0 flag. The behavior is obsolete and is no longer supported.
FreeBSD 14.0-RELEASE-p11 October 21, 2018 FreeBSD 14.0-RELEASE-p11