FreeBSD manual
download PDF document: if_zyd.4.pdf
ZYD(4) FreeBSD Kernel Interfaces Manual ZYD(4)
NAME
zyd - ZyDAS ZD1211/ZD1211B USB IEEE 802.11b/g wireless network device
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device ehci
device uhci
device ohci
device usb
device zyd
device wlan
device wlan_amrr
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
if_zyd_load="YES"
DESCRIPTION
The zyd driver provides support for wireless network adapters based
around the ZyDAS ZD1211 and ZD1211B USB chips.
zyd supports station and monitor mode operation. Only one virtual
interface may be configured at any time. For more information on
configuring this device, see ifconfig(8).
HARDWARE
The following devices are known to be supported by the zyd driver:
3COM 3CRUSB10075
Acer WLAN-G-US1
Airlink+ AWLL3025
Airlink 101 AWLL3026
AOpen 802.11g WL54
Asus A9T integrated wireless
Asus WL-159g
Belkin F5D7050 v.4000
Billion BiPAC 3011G
Buffalo WLI-U2-KG54L
CC&C WL-2203B
DrayTek Vigor 550
Edimax EW-7317UG
Edimax EW-7317LDG
Fiberline Networks WL-43OU
iNexQ UR055g
Linksys WUSBF54G
Longshine LCS-8131G3
MSI US54SE
MyTek MWU-201 USB adapter
Philips SNU5600
Planet WL-U356
Planex GW-US54GZ
Planex GW-US54GZL
Planex GW-US54Mini
Safecom SWMULZ-5400
Telegent TG54USB
Trendnet TEW-424UB rev A
Trendnet TEW-429UB
TwinMOS G240
Unicorn WL-54G
US Robotics 5423
X-Micro XWL-11GUZX
Yakumo QuickWLAN USB
Zonet ZEW2501
ZyXEL ZyAIR G-202
ZyXEL ZyAIR G-220
EXAMPLES
The following example configures zyd0 to join any BSS network using WEP
key "0x1deadbeef1", channel 11:
ifconfig wlan create wlandev zyd0 channel 11 \
wepmode on wepkey 0x1deadbeef1 weptxkey 1 \
inet 192.168.1.1 netmask 255.255.255.0
Join an existing BSS network, "my_net":
ifconfig wlan create wlandev zyd0 192.168.0.2 \
netmask 0xffffff00 ssid my_net
DIAGNOSTICS
zyd%d: could not load firmware (error=%d) An error occurred while
attempting to upload the firmware to the onboard microcontroller unit.
zyd%d: could not send command (error=%s) An attempt to send a command to
the firmware failed.
zyd%d: sorry, radio %s is not supported yet Support for the specified
radio chip is not yet implemented in the driver. The device will not
attach.
zyd%d: device version mismatch: 0x%x (only >= 43.30 supported) Early
revisions of the ZD1211 chipset are not supported by this driver. The
device will not attach.
zyd%d: device timeout A frame dispatched to the hardware for
transmission did not complete in time. The driver will reset the
hardware. This should not happen.
SEE ALSO
intro(4), netintro(4), usb(4), wlan(4), wlan_amrr(4), wlan_ccmp(4),
wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)
AUTHORS
The original zyd driver was written by Florian Stoehr
<ich@florian-stoehr.de>, Damien Bergamini <damien@openbsd.org>, and
Jonathan Gray <jsg@openbsd.org>.
CAVEATS
The zyd driver does not support a lot of the functionality available in
the hardware. More work is required to properly support the IBSS and
power management features.
FreeBSD 14.0-RELEASE-p11 March 7, 2013 FreeBSD 14.0-RELEASE-p11