FreeBSD manual
download PDF document: ieee80211_output.9.pdf
IEEE80211_OUTPUT(9) FreeBSD Kernel Developer's Manual IEEE80211_OUTPUT(9)
NAME
ieee80211_output - software 802.11 stack output functions
SYNOPSIS
#include <net80211/ieee80211_var.h>
int
M_WME_GETAC(struct mbuf *);
int
M_SEQNO_GET(struct mbuf *);
struct ieee80211_key *
ieee80211_crypto_encap(struct ieee80211_node *, struct mbuf *);
void
ieee80211_process_callback(struct ieee80211_node *, struct mbuf *, int);
DESCRIPTION
The net80211 layer that supports 802.11 device drivers handles most of
the work required to transmit frames. Drivers usually receive fully-
encapsulated 802.11 frames that have been classified and assigned a
transmit priority; all that is left is to do crypto encapsulation,
prepare any hardware-specific state, and push the packet out to the
device. Outbound frames are either generated by the net80211 layer (e.g.
management frames) or are passed down from upper layers through the
ifnet(9) transmit queue. Data frames passed down for transmit flow
through net80211 which handles aggregation, 802.11 encapsulation, and
then dispatches the frames to the driver through it's transmit queue.
There are two control paths by which frames reach a driver for transmit.
Data packets are queued to the device's if_snd queue and the driver's
if_start method is called. Other frames are passed down using the
ic_raw_xmit method without queueing (unless done by the driver). The raw
transmit path may include data frames from user applications that inject
them through bpf(4) and NullData frames generated by net80211 to probe
for idle stations (when operating as an access point).
net80211 handles all state-related bookkeeping and management for the
handling of data frames. Data frames are only transmit for a vap in the
IEEE80211_S_RUN state; there is no need, for example, to check for frames
sent down when CAC or CSA is active. Similarly, net80211 handles
activities such as background scanning and power save mode, frames will
not be sent to a driver unless it is operating on the BSS channel with
"full power".
All frames passed to a driver for transmit hold a reference to a node
table entry in the m_pkthdr.rcvif field. The node is associated with the
frame destination. Typically it is the receiver's entry but in some
situations it may be a placeholder entry or the "next hop station" (such
as in a mesh network). In all cases the reference must be reclaimed with
ieee80211_free_node() when the transmit work is completed. The rule to
remember is: net80211 passes responsibility for the mbuf and "node
reference" to the driver with each frame it hands off for transmit.
PACKET CLASSIFICATION
All frames passed by net80211 for transmit are assigned a priority based
transmit them with care, usually by using the transmit rate for
management frames. Multicast/broadcast frames are marked with the
M_MCAST mbuf flag. Frames coming out of a station's power save queue and
that have more frames immediately following are marked with the
M_MORE_DATA mbuf flag. Such frames will be queued consecutively in the
driver's if_snd queue and drivers should preserve the ordering when
passing them to the device.
FRAGMENTED FRAMES
The net80211 layer will fragment data frames according to the setting of
iv_fragthreshold if a driver marks the IEEE80211_C_TXFRAG capability.
Fragmented frames are placed in the devices transmit queue with the
fragments chained together with m_nextpkt. Each frame is marked with the
M_FRAG mbuf flag, and the first and last are marked with M_FIRSTFRAG and
M_LASTFRAG, respectively. Drivers are expected to process all fragments
or none.
TRANSMIT CALLBACKS
Frames sent by net80211 may be tagged with the M_TXCB mbuf flag to
indicate a callback should be done when their transmission completes.
The callback is done using ieee80211_process_callback() with the last
parameter set to a non-zero value if an error occurred and zero
otherwise. Note net80211 understands that drivers may be incapable of
determining status; a device may not report if an ACK frame is received
and/or a device may queue transmit requests in its hardware and only
report status on whether the frame was successfully queued.
SEE ALSO
bpf(4), ieee80211(9), ifnet(9)
FreeBSD 14.0-RELEASE-p11 March 29, 2010 FreeBSD 14.0-RELEASE-p11