FreeBSD manual

download PDF document: openssl-fipsinstall.1ossl.pdf

OPENSSL-FIPSINSTALL(1ossl) OpenSSL OPENSSL-FIPSINSTALL(1ossl)

NAME openssl-fipsinstall - perform FIPS configuration installation
SYNOPSIS openssl fipsinstall [-help] [-in configfilename] [-out configfilename] [-module modulefilename] [-provider_name providername] [-section_name sectionname] [-verify] [-mac_name macname] [-macopt nm:v] [-noout] [-quiet] [-no_conditional_errors] [-no_security_checks] [-self_test_onload] [-corrupt_desc selftest_description] [-corrupt_type selftest_type] [-config parent_config]
DESCRIPTION This command is used to generate a FIPS module configuration file. This configuration file can be used each time a FIPS module is loaded in order to pass data to the FIPS module self tests. The FIPS module always verifies its MAC, but optionally only needs to run the KAT's once, at installation.
The generated configuration file consists of:
- A MAC of the FIPS module file. - A test status indicator. This indicates if the Known Answer Self Tests (KAT's) have successfully run.
- A MAC of the status indicator. - A control for conditional self tests errors. By default if a continuous test (e.g a key pair test) fails then the FIPS module will enter an error state, and no services or cryptographic algorithms will be able to be accessed after this point. The default value of '1' will cause the fips module error state to be entered. If the value is '0' then the module error state will not be entered. Regardless of whether the error state is entered or not, the current operation (e.g. key generation) will return an error. The user is responsible for retrying the operation if the module error state is not entered.
- A control to indicate whether run-time security checks are done. This indicates if run-time checks related to enforcement of security parameters such as minimum security strength of keys and approved curve names are used. The default value of '1' will perform the checks. If the value is '0' the checks are not performed and FIPS compliance must be done by procedures documented in the relevant Security Policy.
This file is described in fips_config(5).
OPTIONS -help Print a usage message.
-module filename Filename of the FIPS module to perform an integrity check on. The path provided in the filename is used to load the module when it is activated, and this overrides the environment variable OPENSSL_MODULES. the -verify option is specified.
-verify Verify that the input configuration file contains the correct information.
-provider_name providername Name of the provider inside the configuration file. The default value is "fips".
-section_name sectionname Name of the section inside the configuration file. The default value is "fips_sect".
-mac_name name Specifies the name of a supported MAC algorithm which will be used. The MAC mechanisms that are available will depend on the options used when building OpenSSL. To see the list of supported MAC's use the command "openssl list -mac-algorithms". The default is HMAC.
-macopt nm:v Passes options to the MAC algorithm. A comprehensive list of controls can be found in the EVP_MAC implementation documentation. Common control strings used for this command are:
key:string Specifies the MAC key as an alphanumeric string (use if the key contains printable characters only). The string length must conform to any restrictions of the MAC algorithm. A key must be specified for every MAC algorithm. If no key is provided, the default that was specified when OpenSSL was configured is used.
hexkey:string Specifies the MAC key in hexadecimal form (two hex digits per byte). The key length must conform to any restrictions of the MAC algorithm. A key must be specified for every MAC algorithm. If no key is provided, the default that was specified when OpenSSL was configured is used.
digest:string Used by HMAC as an alphanumeric string (use if the key contains printable characters only). The string length must conform to any restrictions of the MAC algorithm. To see the list of supported digests, use the command "openssl list -digest-commands". The default digest is SHA-256.
-noout Disable logging of the self tests.
-no_conditional_errors Configure the module to not enter an error state if a conditional self test fails as described above.
-no_security_checks Configure the module to not perform run-time security checks as described above.
-self_test_onload using some other mechanism.
-quiet Do not output pass/fail messages. Implies -noout.
-corrupt_desc selftest_description, -corrupt_type selftest_type The corrupt options can be used to test failure of one or more self tests by name. Either option or both may be used to select the tests to corrupt. Refer to the entries for st-desc and st-type in OSSL_PROVIDER-FIPS(7) for values that can be used.
-config parent_config Test that a FIPS provider can be loaded from the specified configuration file. A previous call to this application needs to generate the extra configuration data that is included by the base "parent_config" configuration file. See config(5) for further information on how to set up a provider section. All other options are ignored if '-config' is used.
NOTES Self tests results are logged by default if the options -quiet and -noout are not specified, or if either of the options -corrupt_desc or -corrupt_type are used. If the base configuration file is set up to autoload the fips module, then the fips module will be loaded and self tested BEFORE the fipsinstall application has a chance to set up its own self test callback. As a result of this the self test output and the options -corrupt_desc and -corrupt_type will be ignored. For normal usage the base configuration file should use the default provider when generating the fips configuration file.
EXAMPLES Calculate the mac of a FIPS module fips.so and run a FIPS self test for the module, and save the fips.cnf configuration file:
openssl fipsinstall -module ./fips.so -out fips.cnf -provider_name fips
Verify that the configuration file fips.cnf contains the correct info:
openssl fipsinstall -module ./fips.so -in fips.cnf -provider_name fips -verify
Corrupt any self tests which have the description "SHA1":
openssl fipsinstall -module ./fips.so -out fips.cnf -provider_name fips \ -corrupt_desc 'SHA1'
Validate that the fips module can be loaded from a base configuration file:
export OPENSSL_CONF_INCLUDE=<path of configuration files> export OPENSSL_MODULES=<provider-path> openssl fipsinstall -config' 'default.cnf'
SEE ALSO config(5), fips_config(5), OSSL_PROVIDER-FIPS(7), EVP_MAC(3)
COPYRIGHT Copyright 2019-2021 The OpenSSL Project Authors. All Rights Reserved.
Licensed under the Apache License 2.0 (the "License"). You may not use