FreeBSD manual
download PDF document: rsu.4.pdf
RSU(4) FreeBSD Kernel Interfaces Manual RSU(4)
NAME
rsu - Realtek RTL8188SU/RTL8192SU USB IEEE 802.11b/g/n wireless network
driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device ehci
device uhci
device ohci
device usb
device rsu
device rsufw
device wlan
Alternatively, to load the driver as a module at boot time, place the
following lines in loader.conf(5):
if_rsu_load="YES"
rsu-rtl8712fw_load="YES"
DESCRIPTION
The rsu driver supports USB 2.0 wireless network devices based on Realtek
RTL8188SU, RTL8191SU and RTL8192SU chipsets.
The RTL8188SU is a highly integrated 802.11n adapter that combines a MAC,
a 1T1R capable baseband and an RF in a single chip. It operates in the
2GHz spectrum only.
The RTL8191SU is a highly integrated multiple-in, single-out (MISO)
802.11n adapter that combines a MAC, a 1T2R capable baseband and an RF in
a single chip. It operates in the 2GHz spectrum only.
The RTL8192SU is a highly integrated multiple-in, multiple-out (MIMO)
802.11n adapter that combines a MAC, a 2T2R capable baseband and an RF in
a single chip. It operates in the 2GHz spectrum only.
These are the modes the rsu driver can operate in:
BSS mode Also known as infrastructure mode, this is used when
associating with an access point, through which all
traffic passes. This mode is the default.
monitor mode In this mode the driver is able to receive packets without
associating with an access point. This disables the
internal receive filter and enables the card to capture
packets from networks which it wouldn't normally have
access to, or to scan for access points.
The rsu driver can be configured to use Wired Equivalent Privacy (WEP) or
Wi-Fi Protected Access (WPA-PSK and WPA2-PSK). WPA is the de facto
encryption standard for wireless networks. It is strongly recommended
that WEP not be used as the sole mechanism to secure wireless
communication, due to serious weaknesses in it.
The rsu driver can be configured at runtime with ifconfig(8).
o Belkin F7D1101 v1
o D-Link DWA-131 A1
o EDUP EP-MS150N(W)
o Edimax EW-7622UMN
o Hercules HWGUn-54
o Hercules HWNUm-300
o Planex GW-USNano
o Sitecom WL-349 v1
o Sitecom WL-353
o Sweex LW154
o TRENDnet TEW-646UBH
o TRENDnet TEW-648UB
o TRENDnet TEW-649UB
FILES
/usr/share/doc/legal/realtek.LICENSE rsu firmware license
The driver needs at least version 1.2 of the following firmware file,
which is loaded when an interface is attached:
/boot/kernel/rsu-rtl8712fw.ko
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev rsu0 inet 192.0.2.20/24
Join a specific BSS network with network name my_net:
ifconfig wlan create wlandev rsu0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev rsu0 ssid my_net \
wepmode on wepkey 0x1234567890 weptxkey 1 up
DIAGNOSTICS
%s: failed load firmware of file rsu-rtl8712fw For some reason, the
driver was unable to read the microcode file from the filesystem. The
file might be missing or corrupted.
device timeout A frame dispatched to the hardware for transmission did
not complete in time. The driver will reset the hardware. This should
not happen.
SEE ALSO
intro(1), netintro(4), rsufw(4), usb(4), wlan(4), networking(7), arp(8),
hostapd(8), ifconfig(8), wpa_supplicant(8)
HISTORY
The rsu driver first appeared in OpenBSD 4.9 and FreeBSD 10.0.
AUTHORS
The rsu driver was written by Damien Bergamini <damien@openbsd.org> and
ported by Rui Paulo <rpaulo@freebsd.org>. The 802.11n support was added
by Adrian Chadd <adrian@freebsd.org>.
CAVEATS
The rsu driver currently does not support 802.11n transmit aggregation,